Ht-instruments FULLTEST3 Manuale Utente Scaricare il pdf (Pagina 48)

FULLTEST 3

EN - 47

The following specific information can be shown on the display during the measurement:

Information displayed Description

Mains voltage was disconnected at too low

momentary voltage (< 20% of peak value). The

message may appear in LINEAR mode only.

Repeat the measurement (connect and disconnect the

UUT again)!

Mains voltage was not disconnected close enough to

peak value (Up ± 5%) so the result would be irelevant

anyway. The message may appear in NONLINEAR

mode only.

Repeat the measurement (connect and disconnect the

UUT again)!

LOW TRIGGER VOLTAGE

REPEAT

LOW SWITCH-OFF VOLTAGE

REPEAT

1 2 ... 43 44 45 46 47 48 49 50 51 52 53 ... 91 92

FULLTEST 1
FULLTEST 3 2
Table of contents: 2
2. GENERAL DESCRIPTION 7
3. PREPARATION FOR USE 10
4. OPERATING INSTRUCTIONS 11
PE-2WIRE function 13
5. MEASUREMENTS 14
Short unisolated wire 15
Red test leads 2,5 mm 15
PE-2WIRE MEASUREMENT 17
NOM (5) 17
PE-4WIRE DISPLAY EXPLANATION 19
PE-4WIRE test result 19
PE-4WIRE MEASUREMENT 21
PE 0  20  21
ISO DISPLAY EXPLANATION 23
ISO test result 23
ISO MEASUREMENT 24
APP or IREAL 27
APP 0  200 mA 28
REAL 0  200 mA 28
TES NOM 28
29
L/N and UL/PE will start to 33
 IN/2 IN 2IN (4) 5IN 33
SC LIM, which is the bases 35
SC MIN must 36
L/N or LOOPL/PE measurement 38
L/N measurement 38
L/L measurement 38
L/PE will start to be 42
IN and actual trigger 47
RES PLUG measurement 47
IN within required range 47
APP 0  5.06 kVA 50
L/N 195  253 V 50
L 0  20 A 50
PE 0.25 mA  10 A 50
L1/2 360  460 V 53
L2/3 360  460 V 53
L3/1 360  460 V 53
CLAMP DISPLAY EXPLANATION 54
CLAMP test result 54
CLAMP measurement 55
LEAK measurement, CLAMP mode 58
L/N 195  253 V 59
PE CURRENT OVERRANGE! 60
L CURRENT OVERRANGE! 60
MEMORY LANGUAGE SETUP 61
OPERATOR TESTER INFO 61
USBCLEARMEM INFO 61
LAST RESULT 62
LANGUAGE 63
TESTER INFO 63
DATE/TIME NOMINAL VOL 64
LEVEL NAMES 64
SAFET INPUT RESETCONTACT VOL 64
50 V25 V 65
CONTACT VOL 65
EN - 65 66
EN - 66 67
EN - 67 68
EN - 68 69
230 V 240 V 70
NOMINAL VOL 70
DISABLED ENABLED 70
SAFETY INPUT 70
7. MEMORY FEATURES 72
8. MEMORIZING EXAMPLE 73
9. RECALL RESULTS 75
EN - 75 76
13. MAINTENANCE 77
A or RCD function 78
PE measurement 79
PE-4WIRE, 25A) 80
PE-2WIRE, 0.2A)) 80
N CAT III 300 V 82
L/PE): 450 k 85
C at IN: 85
TRIG): 0  460 VAC 86
RES): 100 M 86
TRIG): 450 k 86
APP and PACT CAT II 300 V 87
PE (POWER) 87
L1/2, UL2/3, UL3/1 88
CLAMP) 88
15. SERVICE 91

Commenti su questo manuale

Nessun commento

Ht-instruments FULLTEST3 Manuale Utente Pagina 48

Commenti su questo manuale

Prodotti e manuali riguardandi Attrezzi Ht-instruments FULLTEST3